ОргТехСервис
Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация


Коды ошибок принтеров и копиров Kyocera Mita


Коды ошибок принтеров Kyocera Mita FS-800/ 1050/ 1018/ 1118/ 1800/ 3800


Kyocera Mita FS-800



Код ошибкиОписание
E0 - Communication error
  • No communication established between engine and main CPUs
    • E1 - Main motor error
  • Overcurrent in the main motor circuitry due to an excessive torque.
  • Loose connector.
  • Defective CPU on the engine board.
  • No response from the main motor due to the defective motor driver (transistor).
  • Loose CN1 connector on main motor board.
    • E2 - Scanner motor error
  • Scanner motor speed (PLGRDY*) did not reach the predetermined value.
  • Connector insertion error.
  • Defective CPU on the engine board.
  • Time out due to the defective scanner motor driver (transistor).
  • Loose YC302 connector on KP-543.
    • E3 - Scanner pin-photo error
  • No beam hit the photo detector due to the laser diode defect (PD*).
  • Improper connector insertion.
  • Soiled or defective beam detector (pinphoto diode) sensor.
  • Defective safety lock.
  • Inoperative engine CPU.
  • Loose YC604 connector on KP-653board.
    • E4 - Fuser error
  • Blown-out thermistor.
  • Improper connector insertion.
  • Blown-out halogen heater.
  • Comparator defect on the engine board.
  • Defective engine CPU.
  • Loose connection between the fuser unit and CN2 of switching power supply.
    • E9 - Toner motor error
  • Overcurrent in the toner motor circuitry due to an excessive torque.
  • Loose connector.
  • Defective engine CPU.
  • Defective toner motor overcurrent detector.
    • F1 - Controller check sum error
  • Checksum is failed with system ROM (DIMM) on the main controller board.
    • F2 - Controller RAM read/write error
  • Checksum is failed with the RAM on the main controller board.
    • F3 - Controller system error
  • Miscellaneous failure with the main controller, other than F1 and F2.


    • Kyocera Mita FS-1050



    Код ошибкиОписание
    2010 Main motor error
    4000Laser scanner unit [Polygon motor] error
    4200Laser scanner unit [Pin photo diode] error
    5300Eraser lamp error
    6110Fuser unit error
    7980Waste toner full (Total page count less than 100,000 pages of printing)
    7990Waste toner full (Total page count more than 100,000 pages of printing)
    F010Controller checksum error
    F020Controller RAM read/write error


    Kyocera Mita FS-1018/1118



    Код ошибкиОписание
    0220Communication problem between the main board and operation board
    F---Controller system error
    F010ROM checksum error (для FS-1118)
    F012
    7980Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets)
    7990Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more)
    Остальные ошибкиСм. общую таблицу ниже




    Kyocera Mita FS-1800/ 3800



    Код ошибкиОписание
    A0 - Zero cross signal error
  • Defective power supply unit.
  • Defective CPU U201 on the engine board.
    • A2 - Abnomal high temperature error
  • Defective CPU U201 or comparator U205 on the engine board.
  • Defective engine board (KP-864).
  • Defective thermistor.
  • Defective photo coupler on the power supply unit for the heater lamp.
    • E0 - Communication error
  • Defective gate array (U02) on the main board.
  • Connector failure between the engine board (KP-864) and main board (KP-777*1/KP- 858*2).
  • Overrun in the engine system, deactivating the program flash ROM (U202) on the engine board (KP-864).
    • E1 - Main motor error
  • Overcurrent in the main motor circuitry due to an excessive torque.
  • Connector insertion error.
  • Defective gate array U204 on the engine board (KP-864).
  • Defective harness between engine board and engine relay board (KP-760).
  • Defective harness between engine relay board (KP-760) and main motor.
    • E2 - Laser scanner unit (Polygon motor) error
  • Defective gate array U204 on the engine board.
  • Defective polygon motor.
  • Improper connector insertion.
  • Defective harness between laser scanner unit and engine board.
    • E3 - Laser scanner unit (Pin photo diode sensor) error
  • No laser beam due to the laser diode defect (PD*).
  • Soiled or defective pin photo diode sensor.
  • Defective gate array U204 of engine board.
  • Improper connector insertion.
  • Defective harness between engine board and laser scanner unit.
    • E4 - Fuser unit error
  • Blown-out thermistor.
  • Blown-out heater lamp.
  • Defective CPU U201 or comparator U205 on the engine board.
  • Improper connector insertion.
  • Defective power supply unit.
  • Defective harness between fuser unit and power supply unit.
    • E5 - Eraser lamp error
  • Blown-out eraser lamp [board KP-762].
  • Defective CPU U201 on the engine board.
  • Improper connector insertion to the eraser lamp [board KP-762].
    • E9 - Toner motor error
  • Overcurrent in the toner motor circuitry due to an excessive torque, caused by hardened toner.
  • Defective gate array U204 on the engine board.
  • Improper connector insertion.
  • Defective harness between developer and high voltage unit.
  • Defective harness between high voltage unit and engine board.
    • ED - Flash ROM error
  • Defective CPU U201 or gate array U204 or flash ROM U202 on the engine board (KP-864).
    • F0 - LCD controller board error
  • Defective system DIMM [board KP-710*1/ KP-689*2].
  • Defective main board (KP-777*1/KP-858*2).
  • LCD controller board (KP-738).
    • F1 - System DIMM [board] error
  • Defective system DIMM [board KP-710*1/ KP-689*2].
  • Improper system DIMM [board KP-710*1/ KP-689*2] insertion to system DIMM slot on the main board (KP-777*1/KP-858*2).
    • F2 - Main or expanded memory error
  • Defective system main memory (RAM) on the main board (KP-777*1/KP-858*2).
  • Defective main board (KP-777*1/KP-858*2).
  • Defective expanding memory (DIMM) on the main board (KP-777*1/KP-858*2).
    • F3 - General failure
  • Defective main board (KP-777*1/KP-858*2).
    • 99 - Toner refreshing mode error
  • Defective high voltage unit.


    • Коды ошибок копиров Kyocera-Mita KM 1500 / 1505 / 1510 / 1810 / 1820 / 1525 / 1530 / 2030 / 1620 / 2020 / 1635 / 2035 / 1650 / 2050 / 2550 / 2530 / 3530 / 3035 / 4035 / 5035 / 4230 / 5230 / 6230 / 4530 / 5530 / 6330 / 7530 / 6030 / 8030.

  • В первой таблице обобщены ошибки, характерные для всей серии указанных выше копиров, а специфические ошибки для конкретных моделей аппаратов представлены в отдельных таблицах ниже.
  • Коды ошибок представлены в четырехзначной кодировке. Копиры более раннего выпуска, как правило, сообщают о сбоях трехзначным кодом ошибки. Поэтому в таблице у кодов ошибок для таких копиров добавлен один ноль, кроме того опущена буква C. Например, если на индикаторе копира появилась ошибка "C112", то в таблице ей соответствует ошибка "1120".

    Общие коды ошибок копиров Kyocera-Mita :



    Код ошибкиОписание
    0030Fax control PWB system problem
    0070Fax control PWB incompatibility detection problem
    0100Backup memory read/write problem (main board)
    0110Backup memory data problem (main board)
    0120Drum EEPROM read/write problem (для KM-2550)
    0130Backup memory read/write problem (main PCB EEPROM) (для KM-1650/2050/2550)
    0140Backup memory data problem (main PCB EEPROM) (для KM-1650/2050/2550)
    0150Backup memory read/write problem (engine board)
    0160Backup memory data problem (engine board)
    0170Accounting count problem
    0180Machine number mismatch
    0210Communication problem between the main board and engine board (для KM-1500/1620/2020/1635/2035/1650/2050/2550/6030/8030)
    Communication problem between the main board and operation board (для KM-1525/1530/2030/2530/3530/6230/4530/5530/6330/7530)
    0240Printer board PWB communication problem
    0250Scanner network board communication problem
    0280Communication problem between the fax control PWB and main PWB
    0320Side deck communication problem
    0340Finisher communication problem
    0410Optional DP communication problem
    0420Optional first paper feeder communication problem
    Large paper deck /Side deck communication problem
    0440Finisher communication problem
    0450Mailbox communication problem
    0470Switchback unit communication problem
    0500Optional second paper feeder communication problem
    0510Optional third paper feeder communication problem
    0600DIMM problem (для KM-2530/3530)
    0610Bitmap (DIMM) problem
    0620Memory input interface problem
    0630DMA problem (Direct Memory Access)
    0640Hard disk drive problem
    0800Image processing problem (JAM 05 is detected twice)
    0820Fax control PCB CG ROM checksum error
    0830Flash ROM program area checksum error
    0860Fax control PCB software switch checksum error
    0870Fax control PWB to main PWB high capacity data transfer problem
    0880Fax control PWB program archive problem
    0890Fax control PCB CG font archive problem
    0900Fax software incompatibility detection problem
    0920Fax file system error
    0960Developer EEPROM read/write problem (для KM-2550/6030/8030)
    1000Exposure lamp problem
    1010Lift motor 1 error
    1020Lift motor 2 error
    1030Lift motor 3 error
    1040Lift motor 4 error
    1100Paper deck motor 1 problem [Drawer 3]
    1110Paper deck motor 2 problem [Drawer 4]
    1120Deck right lift position problem
    1130Deck left lift position problem
    1140Side deck lift motor (going up) problem
    1150Side deck lift motor (going down) problem
    1160Large paper deck (paper feed desk) sequence problem
    1170Large paper deck (paper feed desk) incorrect type problem
    2000Main motor problem
    Image forming motor problem (для KM-6230/4530/5530/6330/7530)
    2500Paper feed motor problem
    2550Paper conveying motor problem (для KM-4530/5530)
    2600Deck conveying motor /desk drive motor problem
    2640Side deck drive motor problem
    3100Scanner carriage problem
    3200Exposure lamp problem
    3300Optical system (AGC) problem
    4000Polygon motor synchronization problem
    4010Polygon motor steady-state problem
    4100BD initialization (A) problem
    4110BD initialization (B) problem
    4200BD steady-state problem
    5100Main charger problem
    5110Transfer/separation high voltage problem
    5300Broken cleaning lamp wire
    5500Drum surface potential sensor problem 1
    5510Drum surface potential sensor problem 2
    5600Drum surface potential problem 1
    5610Drum surface potential problem 2
    6000Broken fixing heater wire
    6020Abnormally high fixing unit thermistor temperature
    6030Broken fixing unit thermistor
    6050Abnormally low fixing unit thermistor temperature
    6100Broken fixing heater wire
    6200Abnormally low fixing unit thermistor temperature
    6300Abnormally high fixing unit thermistor temperature
    6400Zero-crossing signal problem
    6410Fixing unit connector insertion problem
    6420Fixing fuse cut problem
    6420Broken fixing unit thermistor wire
    7100Toner sensor problem
    7300Broken external temperature thermistor wire (для KM-1505/1510/1810/4230/5230/6230)
    Toner sensor problem /Toner hopper problem (для KM-2530/3530/3035/4035/5035/6230/4530/5530/6330/7530/6030/8030)
    7310Short-circuited external temperature thermistor
    7400Image formation unit connector insertion problem
    Developing unit connector insertion problem (для KM-2550)
    7410Drum unit connector insertion problem
    7750Drum type mismatch problem A (для KM-1635/2035)
    7760Drum type mismatch problem B (для KM-1635/2035)
    7800Broken external temperature thermistor
    7810Short-circuited external temperature thermistor
    7980Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets)
    7990Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more)


    Kyocera KM-1505/1510/1810/1525/1530/2030



    Код ошибкиОписание
    0210Printer board communication problem (для KM-1505/1510/1810)
    0400DIMM problem
    0410Bitmap problem
    0430DMA problem (Direct Memory Access)
    1040Optical system problem (AGC)


    Kyocera-Mita KM 3035/4035/5035



    Код ошибкиОписание
    0100Operation unit PCB backup memory read/write error
    0110Operation unit PCB backup memory data problem
    0210MMI communication problem
    0320Energy save communication problem
    7450Image formation unit fuse cut problem


    Kyocera Mita KM 4230/5230



    Код ошибкиОписание
    0010Memory copy PCB 1 communication problem
    0030Memory copy PCB 2 communication problem
    0100RAM/ROM problem
    0220Communication problem between the engine PCB and main PCB
    0230Scanner communication problem
    0260Memory copy PCB 1 communication problem
    0320Large paper deck communication problem /Paper feed desk communication problem
    0360Memory copy PCB 2 communication problem
    0370Communication microcomputer problem
    1040Optical system problem (AGC)
    2100Paper conveying motor problem
    2200Side registration motor problem
    2300Paper feed motor problem
    2310Desk drive motor problem
    2410Upper lift motor problem
    2420Lower lift motor problem
    2430Upper desk lift motor problem
    2440Lower desk lift motor problem
    3320Scanner watchdog problem
    3400Original detection position problem
    7400Toner hopper problem
    9200Deck paper conveying motor problem
    9210Paper deck motor 1 problem
    9220Paper deck motor 2 problem
    9230Right lift position problem
    9240Left lift position problem


    Kyocera Mita KM 6030/8030



    Код ошибкиОписание
    0060Main PWB type mismatch error
    0130Backup memory (EEPROM) device problem
    0140Backup memory (EEPROM) data problem
    0220Scanner communication problem
    0330Relay board communication problem
    0460Duplex unit communication problem
    0470Sheet inserter communication problem (optional document finisher)
    0500Paper feed unit communication error (cassette 1 and 2)
    0510Paper feed unit communication error (cassette 3 and 4)
    0700Side feeder EEPROM error (optional side feeder)
    0750Document finisher EEPROM error
    0970Cleaning unit EEPROM error
    1200Duplex side registration motor error
    2100Developing motor error
    2200Drive motor error
    2300Fuser motor error
    2550Transfer motor error
    3210CIS lamp problem
    3310Optical system (AGC) problem (DP)
    3500Communication error between scanner and SHD
    3900Backup memory read/write error (scanner PWB)
    3910
    4120BD initialization (C) problem
    7200Broken drum thermistor wire
    7210Shorted drum thermistor
    9040DP lift motor going up error
    9050DP lift motor going down error
    9060DP EEPROM error
    9070Communication problem between DP and SHD
    9080Communication problem between DP and CIS


    Kyocera Mita KM 6230



    Код ошибкиОписание
    0010Memory PCB communication problem
    0100RAM/ROM problem
    0260Memory copy PCB 1 communication problem
    0350Mailbox communication problem
    0370Communication microcomputer problem
    0380Hard disk problem
    0390DIMM problem
    1040Optical system problem (AGC)
    2100Drive motor problem / Paper conveying motor problem
    2200Paper feed motor problem
    2300Large paper deck right lift motor problem
    2310Large paper deck left lift motor problem
    2420Upper lift motor problem
    2430Lower lift motor problem
    6500Broken fixing unit thermistor wire
    7200Broken drum thermistor wire
    7210Shorted drum thermistor
    7220Broken drum heater wire


    Kyocera Mita KM 6330/7530



    Код ошибкиОписание
    1060Large paper deck left lift motor problem
    2550Drive motor problem
    7520Shorted drum thermistor
    7530Broken drum thermistor wire




    Как войти в сервисный режим копиров Kyocera Mita (KM):



    Аппарат Процедура входа в сервис
    Kyocera КМ-1505/1510/1810/1500
  • Последовательно нажимаем кнопки: "Стоп/Сброс", "Старт" и левую кнопку регулировки плотности копий.
  • Отпускаем и опять нажимаем кнопку "Стоп/сброс".
  • Номер сервисной команды выбираем клавишами масштабирования или регулировки контрастности.
  • Сброс печных ошибок и ошибки Zero Cross осуществляется сервисной командой 163, после ввода надо нажать два раза кнопку "Старт", затем выключить и включить аппарат.
    		•
    Kyocera КМ-1525/1530/2030/1620/1650/2050 и многих других.
  • Набираем кнопками количества копий: 10871087.
  • Выбираем сервисную команду - курсором вверх/вниз ( KM-2030), кнопкой масштабирования +/-" (KM-1530), или кнопками количества копий.
  • Ввод данных - кнопкой "Старт".
  • Сброс печных ошибок и ошибки Zero Cross осуществляется сервисной командой 163, "Старт", выбираем "Execute" (только для KM-2030), нажимаем "Старт".
  • Сброс маслёнки: сервисной командой 251, кнопкой выбора контрастности выбираем позицию 3 контрастности, нажимаем "Старт".
  • Для выхода из сервисного режима - у некоторых машин таких как, например, KM-1620 надо ввести 001, затем нажать кнопку "Старт", у большинства - нажать кнопку "Сброс" или просто выключить и включить аппарат.


    • Коды ошибок принтера Kyocera FS-1120d, 1320d
    Коды ошибок мфу Kyocera FS-1020MFP, 1025MFP, 1120MFP, 1125MFP, 1220MFP, 1320MFP, 1325MFP
    Коды ошибок мфу Kyocera FS-1030MFP, 1035MFP, 1130MFP, 1135MFP, сброс ошибок.
    Коды ошибок мфу Kyocera FS-2020d, FS-3920dn, FS-4020dn
    Коды ошибок мфу Kyocera FS-3040MFP, FS-3140MFP


    • Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация

    Rambler's Top100 Рейтинг@Mail.ru