ОргТехСервис
Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация


Коды ошибок HP LaserJet Pro MFP m226 dn, dw


Код ошибки

Дисплей

Описание

Устранение проблемы

13.0000 13.0000 Paper jam  
20.0000 20.0000 Memory out  
21.0000 21.0000 Page misfeed or mispick  
41.2000 41.2000 Beam detect malfunction  
41.3000 41.3000 Unexpected size  
49 49 Error The product has experienced a firmware error. 1. Press the power button to turn the product off. 2. If a surge protector is being used, remove it. Plug the power cord directly into a wall outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the error persists, disconnect and then reconnect the FFCs and the connectors on the formatter PCA. 5. If the error persists, replace the formatter PCA.
50.0000 50.0000 Fuser error  
50.1000 50.1000 Low fuser temperature error  
50.2000 50.2000 Slow fuser error  
50.3000 50.3000 High fuser temperature error  
50.4000 50.4000 Fuser drive circuit error  
50.7000 50.7000 Fuser open error. Low sub-thermistor fuser error. High sub-thermistor fuser error  
50.X 50.X Fuser Error The product has an internal hardware error. 1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet.3. Wait at least 25 minutes, turn the product on, and then wait for the product to initialize.4. If the error persists, reconnect J101 and J552 on the engine controller PCA.5. If the error persists, check the power source. Make sure that the power source meets the minimum system requirements (40Hz to 70Hz).6. If the error persists, replace the fuser.7. If the error persists, replace the engine controller PCA.
51.0000 51.0000 Beam detect or laser error  
51.2000 51.2000 Black scanner laser error (inline devices only)  
51.XX 51.XX Error The printer has experienced an internal hardware error. The product may display the following message: 51.20 Black laser scanner error Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer. If the message persists, contact HP support.
52.0000 52.0000 Engine laser scanner error  
54.0100 54.0100 Environmental sensor error Verify that the DC controller connectors are firmly connected. If the error persists, replace the temperature/humidity sensor. If the error persists, replace the DC controller.
54.0600 54.0600 Density sensor error Verify that the cables between the DC controller is firmly connected.
54.1100 54.1100 Black density out of range If the error persists, replace the color misregistration sensor.
54.1200 54.1200 Black density measurement abnormality If the error persists, replace the DC controller.
54.1599 54.1599 Black CPR pattern cannot be read 1. Turn off the power by using the power switch, and then wait at least 30 seconds.2. Turn on the power and wait for the product to initialize. If the error persists, verify that the cables between the color misregistration sensor and the DC controller are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the toner cartridge tray. If the error persists, replace the DC controller.
54.1600 54.1600 Black CPR pattern cannot be read 1. Turn off the power by using the power switch, and then wait at least 30 seconds.2. Turn on the power and wait for the product to initialize. If the error persists, verify that the cables between the color misregistration sensor and the DC controller are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the toner cartridge tray. If the error persists, replace the DC controller.
54.2100 54.2100 Beam detect (BD) error If the error persists, replace the DC controller. If the error persists, replace the product.
54.2500 54.2500 Top-of-page sensor error Verify that the DC controller connectors are firmly connected. If the error persists, replace the DC controller.
54.XX 54.XX The printer has experienced an error with one of the internal sensors. The product may display one of the following messages:• 54.18 Black toner level sensor error• 54.19 TOP sensor error• 54.1200 Black density measurement abnormality• 54.1500 Black CPR pattern cant be read• 54.21 BD errors Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer. If the message persists, contact HP support.
55.3000 55.3000 Engine-formatter communication error  
55.4000 55.4000 Engine communication timeout error  
55.X 55.X Error The printer has experienced an internal error. The printer may experience one of the following errors:• 55.0 DC controller communication error• 55.0601 DC controller NVRAM data error• 55.0602 DC controller NVRAM access error• 55.1 DC controller memory error Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer.
57 57 Fan Error The product has a general fan error. 1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet.3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize.4. If the error persists, reconnect the J1103 connector on the duplex connector PCA.5. If the error persists, replace the main fan.
57.0000 57.0000 Fan motor error  
57.0600 57.0600 Fan motor error  
59.X 59.X Error The printer has experienced a problem with one of the motors. The product may display one of the following errors:• 59.3 Fuser motor startup error• 59.4 Fuser motor rotation error• 59.50 Image drum motor startup error - black• 59.73 Developer motor startup error• 59.83 Developer motor rotation error• 59.C0 Developer motor rotation error• 59.F0 Transfer alienation failure Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer.
79 79 Error The product has experienced a firmware error 1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet.3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize.4. If the error persists, disconnect and then reconnect the FFCs and the connectors on the formatter PCA.5. If the issue persists, replace the formatter PCA.

мфу HP Pro m226dn, dw, HP M226, ошибка 13.0000, 20.0000, 21.0000, 41.2000, 41.3000, 49, 50.0000, 50.1000, 50.2000, 50.3000, 50.4000, 50.7000, 50.X, 51.0000, 51.2000, 51.XX, 52.0000, 54.0100, 54.0600, 54.1100, 54.1200, 54.1599, 54.1600, 54.2100, 54.2500, 54.XX, 55.3000, 55.4000, 55.X, 57, 57.0000, 57.0600, 59.X, 79,

как сбросить ошибку hp m226 dn, dw, коды ошибок HP Pro m226 dn, MFP, HP LaserJet Pro m226 dw, HP M226, HP M226 ошибка


Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация

Rambler's Top100 Рейтинг@Mail.ru